Atlona Help Center

KB01274 - How to use and interpret the HDBaseT Analyzer

SKU: AT-HDR-EX-70-2PS

Subject: How to use and interpret the HDBaseT Analyzer

Steps: The AT-HDR-EX-70-2PS extender set allows the user to perform an HDBaseT analysis using the software found here. This article will explain how to use the software and how to interpret its test results. this article was written for the product control software V2.6.

Step 1: Download

Step 2: Launching software

  • After installing the software and launching it, you will see the software like so:
  • If you have issues finding the devices, check the “Port” area at the top of the software: While the device will try to automatically select the correct COM Port, multiple units or com devices connected to the computer can cause there to be multiple available com ports. You may access your “Device Manager” on a Windows PC to verify which port has the “Prolific USB-to-Serial Comm Port” present:

For a step-by-step guide on how to locate and use Device Manager on Windows 7/8/10 machines, please see this article.

Step 3: Using the software

  • In the bottom left corner, step by step instructions are provided for hooking up the extenders to the software. These instructions are:
    • While the units are powered off, set the dip switch on the bottom of each unit to the right so its set to HDBaseT:  
    • Plug the power supplies of both the TX and RX unit in and screw the locking connector down.
    • Connect an HDMI source to the transmitter and an HDMI display to the receiver.
    • Verify that everything is set up to pass video from the source to the display. While video may not pass, its important to ensure your source is sending video and the display is able to accept video as the HDBaseT test will analyze the connection path and confirm if there are any issues with the bandwidth capabilities of the cable.
    • Set the dip switch on each unit to UNIT.
    • Connect a PC running the HDBaseT Analyzer Software to the FW USB port of either the TX or RX (you can connect to either unit).
    • Click the START button ().
    • The test will now run.
    • After the test is complete, set the dipswitch on both units to HDBaseT.

Step 4: Interpreting Signal Information Test Results

  • After the test is complete, you will see the software update the “Signal Information” and “Signal Quality” sections with data. You will also see the UNIT Firmware (FW) version of whichever device you are connected to under the FW version. Please see this article for an explanation of the various dipswitch settings on the HDR-EX-70 units.
  • After pressing the START button () , you will see the signal information and signal quality fields populate with information:
  • Signal information reports back the data regarding the signal being passed and the connection between source and display. When passing a good signal, you should see "ON" () for HDBaseT Link, HDMI 5V and HPD.
    • HDBaseT Link is the link between TX and RX. This will confirm that the TX and RX units are able to see each other. If you see "OFF" () then this means there may be an issue with the CAT cable being used. Please try another CAT cable (preferably one that has been known to work with other extenders).
    • HDMI 5V (5-volt) refers to the 5-volt signal an HDMI source sends out along with the video/audio information. This allows an HDMI source to read the EDID information of a display as well carry video from the source to the display. A lack of adequate 5V current can cause issues with signal pass-through.
    • HPD (Hot Plug Detect) is the communication passed from a source to an HDMI/DVI display which allows the display to be aware that a signal is being passed to it. This is what will cause monitors to turn themselves on from a standby state when a source begins passing signal to them. Issues with HPD can cause a display to stay in standby mode or report not having a signal.
    • TMDS Clock (Transition Minimized Differential Signaling) is a method for transmitting high-speed digital information. This uses a unique algorithm that helps reduce electromagnetic interference (EMI) and enables the HDMI clock signal to stay synced, even at long transmission distances. This number will fluctuate based on the resolution being passed. A 0 value implies issues with the CAT or HDMI cables.
      • Typically, a UHD signal (i.e. 3840x2160@30hz – 4:2:0) will use 300Mhz clock
      • A HDR (4K@60Hz – 4:4:4) will use 600Mhz clock
    • Cable length (estimated) is used to estimate the length of cable being used. While this number is not 100% exact, it helps you get an estimate of the CAT cable being used to see if its within specifications for the extenders.
    • Video Quality (video BER) is the BIT error rate for the video signal. This is the number of bit errors per a specific unit of time. The bit error ratio (also BER) is the number of bit errors divided by the total number of transferred bits during a studied time interval. This area will only report a numerical value (in RED) if there is an error with video quality. Otherwise, you will see a green “Pass” as shown. However, video quality issues (such as dots appearing on the screen) may not be visually noticeable, even if the HDBaseT test reports errors being present. If you can visually confirm that errors are present, consider replacing your HDMI cables on both ends (try using cables under 15ft in length), consider trying another CAT cable, and lastly, consider trying another resolution or another video source to see if the same visual issues are present. If you do not see any errors in video playback, but had the test report a value for Video Quality, you do not need to be concerned.

Step 5: Interpreting Signal Quality

  • The Signal Quality test analyzes all 4 pairs of a 568B terminated CAT cable (for a total of 8 conductors). Please note, if you are using a 568A termination, the pins shown in the software’s diagram will not match your cables pin out (the test results should be the same). With this test, you want all 4 pairs to show a "PASS" () :
  • If you notice any pair showing as not passing, please consider using a new CAT cable or re-terminating the existing one.

Step 6: Analyzing Firmware

  • After connecting to either the TX or RX and running the HDBaseT test, you will be able to see the firmware version of the device you are communicating with. To check the firmware of the other device, simply hit "STOP" () on the current test. Next, connect your USB cable to the “FW” port on the other device and hit "START" ().
  • When connected to the TX or RX (either one) you will see a TX and RX HDBaseT Version. This is the firmware version of the HDBaseT chip being used.
  • You can also perform firmware updates using this software. When new firmware is available, you will simply download the firmware file, browse for it on your PC using this software and hit load. The status bar below the Browse area will give you the current update status.

Step 7: Starting Debug mode, saving log

  • The HDR-EX-70-2PS extenders also allow you to run a debug mode which will capture all data being processed by the extender set. This is helpful in troubleshooting unexplainable occurrences. To run this simply click "STOP" () on the HDBaseT test and click "Debug" (). After this, the text box below Debug will show all data being processed. This information may be hard to interpret so you can use "Save" () to save the log file and share it with Atlona Technical Support for further assistance. An example of a debug being run:

 

Step 7: Concluding testing

  • After conducting testing, simply click "Stop" () on any testing being performed and disconnect the USB cable from the TX/RX unit. Then perform a power cycle on both TX and RX to ensure they are back to their normal operating state.

Article ID: KB01274 

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Contact Us